Smart Home Guide

Why Is My WiFi So Slow? A 10-Minute Diagnosis for Singapore Homes

By Roen Team 13 November 2026 11 min read
Why Is My WiFi So Slow? A 10-Minute Diagnosis for Singapore Homes

If you are asking why is my WiFi so slow, start here: “slow WiFi” is two different faults that look identical on a phone. Either the internet line into the home is slow, or the line is fine and the WiFi is not carrying it to the room you are sitting in. In Singapore homes it is usually the second, in installer practice: fibre arrives at a box near the front door, and concrete does the rest. The checks below take about ten minutes with a laptop, a LAN cable and any speed test, in the order an installer would run them. The first two tell you which half of the problem you have.

Why is my WiFi so slow? Two tests split the line from the WiFi

Test 1: wired at the router, then WiFi beside it

Fibre enters the home at the Optical Network Terminal (ONT), the small box the fibre cable plugs into, and the router plugs into the ONT. Connect a laptop to a LAN port on the router with a cable, switch the laptop’s WiFi off, pause downloads on everything else and run a speed test. The telcos’ own support guides describe the same check: one computer on a LAN cable, everything else disconnected, result compared with the plan. Plan speeds are measured this way too: M1’s published typical speeds were taken on computers cabled to the ONT. Now unplug, stand beside the router and repeat the test over WiFi.

If the wired number is slow, the fault is the line, the plan, the router or the cable, not the WiFi. If wired is fast and WiFi is not, the broadband is fine and the WiFi is the problem; the providers’ guides draw the same line. One caution: a gigabit laptop port cannot show more than a gigabit, and IMDA notes that full 10 Gbps performance needs 10GbE ports on computer and router and a Cat6 or better cable.

Test 2: beside the router, then in the slow room

Take the same device to the room that annoys you and test again. Fast beside the router and slow in the bedroom is a coverage problem: distance, walls or where the router sits. Slow even beside the router, with a fast wired result, points at the router’s WiFi itself: band, channel, load or age. The coverage case is the one that survives every free fix, and it is what a WiFi installation Singapore team exists to solve.

Slow WiFi symptoms: what each result points to

Symptom Likely cause Fix Cost
Slow on the cable at the router Line, plan, ONT or router; a loose or old LAN cable Restart ONT and router, swap the cable, then call the ISP Free
Cable fast, WiFi slow even beside the router Device on 2.4 GHz, crowded channel, overloaded or ageing router Join the 5 GHz band, change channel, restart Free first, a new router if not
Fast near the router, slow in the far bedroom Concrete walls and distance Move the router into the open; add an access point or mesh node Free, then hardware or cabling
WiFi slow only in the evening Neighbours’ networks plus your own household peak Move devices to 5 GHz; set 2.4 GHz to channel 1, 6 or 11 Free
Cameras stutter, smart plugs drop offline Too many devices crowded on 2.4 GHz Separate network for smart devices; cable what can be cabled Free, then hardware
Slow in the room with the extender The extender is relaying a signal that is already weak Move it halfway, or replace it with a wired access point Free, then cabling
Wired speed stuck just under 100 Mbps An old Cat5 or damaged cable somewhere in the chain Replace the patch cable; test the wall run A new cable, or cabling work
Suddenly slow everywhere Something changed this week Restart, then check new devices, cables and the cupboard door Free

WiFi slow in one room: bands, concrete and where the router sits

2.4 GHz or 5 GHz: check which one the device is on

Most home routers broadcast on two bands. 2.4 GHz reaches further but is slower and more crowded; 5 GHz is faster and does not reach as far. Open the WiFi settings on the slow device and see which it has joined. In practice a phone that latched onto 2.4 GHz at the far end of the flat tends to stay there, so toggle its WiFi off and on. If the router shows two network names, put laptops, phones and TVs on the 5 GHz one and leave 2.4 GHz to the gadgets that need it.

Reinforced concrete walls and the household shelter

Singtel’s own guide says it directly: WiFi weakens through walls, especially reinforced concrete, and through metal. Roen’s network page says the same of HDB flats: concrete walls eat 5 GHz signal. The hardest case is the household shelter, which HDB describes as fitted with a steel door and strengthened floor, walls and ceiling. A router kept in the shelter is boxed in. No setting fixes concrete: the signal either goes round it, by moving the router, or starts on the other side, from a second radio.

The router in the DB cupboard or behind the TV

In practice the router ends up wherever the fibre point is, often a cupboard by the door or the TV console. Both telcos warn against it: Singtel lists routers in DB boxes and cabinets among the causes of poor coverage, and StarHub says not to hide the router behind the TV, in a storeroom or on the floor. Open the cupboard door and rerun Test 2. Better, use a longer LAN cable between ONT and router so the router sits on an open shelf near the middle of the home. It is the cheapest real fix in this guide.

Slow WiFi at night: neighbours and channel congestion in HDB and condo blocks

The 2.4 GHz band has only three channels that do not overlap (1, 6 and 11), and every router above, below and beside you shares them; TP-Link counts 23 on 5 GHz. Singtel names interference from nearby networks in dense HDB and condo living as a cause of slow WiFi, and StarHub puts the worst of it in the evening peak, 7 pm to 11 pm. Microwave ovens and cordless phones add to the noise on 2.4 GHz. The fixes are free: move everything that supports it to 5 GHz. In the router’s settings, set 2.4 GHz to channel 1, 6 or 11, picking the quietest with a free WiFi analyser app. Leave the transmit power alone: in practice a louder router only shouts into the same crowd.

Too many devices, and smart-home gadgets crowding 2.4 GHz

Count what is connected. One telco guide notes that with 15 to 20 devices online at once each gets a smaller slice, and a home with smart plugs, bulbs, TVs and cameras passes that easily. Many smart-home gadgets join on 2.4 GHz only, so they pile onto the band that is already crowded. Remove devices you no longer use. Give smart devices their own network name on 2.4 GHz so they stop competing with laptops. And take the heavy talkers off the air: CCTV cameras on a network cable upload over the wire instead of over WiFi, and sensors and switches can run on Zigbee through a hub, as our comparison of Zigbee vs WiFi vs Matter explains.

Extenders, mesh hops, old routers and Cat5: hardware that caps a fast plan

A plug-in extender repeats what it hears from the router, so in the dead room it repeats a signal that is already poor. A wireless mesh pays a similar toll: as Roen’s service page puts it, each wireless mesh hop can roughly halve throughput, while a wired access point keeps full speed. Put the extender or satellite halfway, where the signal is still strong, or give it a cable; mesh WiFi vs extender covers that choice.

The same guide says a router more than three to four years old likely runs WiFi 5 or older and struggles with ten or more devices, and IMDA advises a minimum of WiFi 6E or WiFi 7 for 10 Gbps plans. Cables cap speed as well: old Cat5 tops out at 100 Mbps, Cat5e carries up to 1 Gbps, and Cat6 or Cat6a up to 10 Gbps, so one tired patch lead between ONT and router can throttle the whole home. Read the print on the cable jacket; Cat5 vs Cat6 shows what to look for.

Why is my WiFi so slow all of a sudden? Check what changed

WiFi that was fine last month has not aged overnight. Something changed. A new device, often a camera or a console downloading updates. A router that got pushed behind something, or a cupboard door that now stays shut. A cable knocked half out; the telco guides note that even a partly disconnected cable causes packet loss. Restart first, since it is free: the standard telco routine is to power off the ONT and router, wait two minutes, power on and wait for steady lights. Then rerun Tests 1 and 2. If the wired result has dropped as well, it is not your WiFi.

Is it the fibre line or the WiFi? The same checks apply on every Singapore plan

Whichever telco supplied the router, the diagnosis does not change with the logo on it. Fibre arrives at an ONT, the router has the same bands, and concrete treats every brand alike. Use the provider’s own tools first: every major provider publishes a restart and wired-test routine, and most have an app that shows the line status. To keep the supplied router and add your own access points or mesh, our guide on how to set up a home network explains how the two fit together.

How to fix slow WiFi: what is free and what needs hardware or cabling

Level What it covers Solves
Free, today Restart ONT and router; move the router into the open; put devices on 5 GHz; set the 2.4 GHz channel; remove idle devices; reseat cables Congestion, bad placement, sudden slowdowns
Hardware A current router; a mesh node placed halfway; a new Cat6 patch cable An ageing router, a compact home with one weak corner
Cabling A network cable to the far rooms and an access point on the end of each Rooms behind concrete, long condos, multi-storey landed homes

Work down the table and stop at the first row that fixes it. A faster plan is left out on purpose: if the wired test already shows the speed you pay for, a bigger plan only raises the number at the router. Where the far room still fails after the free fixes, the lasting answer is a cable to that room, which is what structured cabling for the home means.

Who to call: the ISP or an installer

The two tests answer “why is my WiFi so slow”; they also tell you whose job the fix is. Call the ISP when the wired test at the router is slow, when the ONT or router shows warning lights, or when the connection drops on cable as well as WiFi. The line, the ONT and a supplied router are theirs to check.

Call an installer when wired is fast and rooms are slow, and moving the router has not cured it. Roen is a Singapore smart-home installer and integrator. It surveys, designs, installs and configures home WiFi and networks for HDB, condo and landed homes: a signal survey first, then mesh or wired access points and the cabling behind them, with brand-neutral advice on equipment. Roen does not work on the line itself, so a slow wired result stays with your ISP.

Frequently asked questions

How can I fix my slow WiFi speed?

Run the two tests first, so you know how to fix slow WiFi in your home and not in general. Then restart the ONT and router, move the router out of the cupboard, put your main devices on 5 GHz and set the 2.4 GHz channel to 1, 6 or 11. If the far rooms are still slow, they need a mesh node or a wired access point.

Why is my WiFi so bad all of a sudden?

Because something changed: a new device, a moved router, a loose cable, a neighbour’s new network or a fault on the line. Restart the ONT and router, then test on a cable. A slow wired result means the ISP; a fast one means the change is inside your home.

Is 20 Mbps slow or fast?

It is enough for one stream: Netflix recommends 5 Mbps for Full HD and 15 Mbps for 4K. But home fibre plans in Singapore are sold in gigabits, so 20 Mbps in a bedroom means only a small fraction of the plan is arriving there.

How do I tell what is slowing down my WiFi?

Compare three speed tests: on a cable at the router, on WiFi beside the router, and on WiFi in the slow room. The step where the number falls names the cause: the line, the router’s WiFi, or the walls and distance in between.

Why is my WiFi slow when my fibre plan is fast?

The plan sets the speed at the ONT, not in the bedroom. If you are still asking why is my WiFi so slow after an upgrade, the limit is between the router and you: band, channel, concrete, an extender hop or an old cable.

Does restarting the router fix slow WiFi?

Sometimes, and it costs nothing. The routine is to power off the ONT and router for two minutes, then power on. It clears a stuck router; it cannot move a wall.

Wired is fast but the bedrooms are not?

That is a coverage problem, and it is the part Roen handles: a signal survey of the home, a design that fits the walls, mesh or wired access points where the readings say, and the cabling to feed them. Call or WhatsApp 8986 1961.

Planning a smart home install?

Tell us what you have in mind and the Roen team will come back to you.

WhatsApp 8986 1961 Contact us