Smart Home Guide

How to Check WiFi Signal Strength at Home and Fix the Weak Spots (Singapore)

By Roen Team 13 November 2026 13 min read
How to Check WiFi Signal Strength at Home and Fix the Weak Spots (Singapore)

WiFi signal strength is the number behind every “the WiFi is bad in the back room” complaint, and almost nobody has looked at it. This guide shows what the dBm figure means, how to check WiFi signal strength on an iPhone, Android, Windows or Mac without buying anything, how to test it room by room, the causes specific to HDB flats, condos and landed homes, the free fixes, and which hardware fixes a weak spot for good.

WiFi signal strength: what the dBm numbers actually mean

Signal strength is measured in dBm, decibel-milliwatts, and it is always a negative number. The closer to zero, the stronger the signal: -45 dBm is excellent, -75 dBm is poor. The scale is logarithmic, so every 3 dB is roughly a halving of power and the gap between -60 and -70 is far larger than it looks. Bars are a loose translation of this number and every phone maker draws them differently, which is why three bars on one phone can be a better connection than four on another.

Reading (dBm) Rating What it supports in practice
-30 to -50 Excellent Same room as the router or node. Anything works, including 4K streaming and large uploads.
-50 to -60 Good Video calls, 4K streaming, gaming, several devices at once. The target for every room you work or watch in.
-60 to -67 Fair Browsing, HD streaming and smart home devices are fine. -67 dBm is the floor most engineers use for reliable voice and video calls.
-67 to -70 Weak Pages load, calls start to freeze, cameras buffer, devices hop between bands.
-70 to -80 Poor Slow and unreliable. 2.4 GHz smart plugs show as offline, phones fall back to mobile data.
Below -80 Unusable The device sees the network but cannot hold a connection worth having.

Noise matters too: -65 dBm signal against -95 dBm noise is comfortable; the same signal against -80 dBm noise, normal in a dense HDB block at 9 pm, is not.

How to check WiFi signal strength on iPhone, Android, Windows and Mac without an app

iPhone. iOS does not show dBm in Settings. Install Apple’s free AirPort Utility, switch on Wi-Fi Scanner for it in the Settings app, then open the app and tap Wi-Fi Scan. It lists every network with its RSSI, the dBm figure, and refreshes as you walk.

Android. Settings, then Network and internet (Connections on Samsung), tap your network, then its details. Many Pixel and Samsung models show the dBm value; if yours shows only Excellent, Good or Fair, a free WiFi analyser app shows the number.

Windows 11. Open Command Prompt and type netsh wlan show interfaces. The Signal line is a percentage, not dBm; as a rule of thumb 100% is about -50 dBm, 50% about -75 dBm and 30% about -85 dBm. The same output shows the band and channel.

Mac. Hold Option and click the WiFi icon in the menu bar. The panel shows RSSI (signal), Noise, channel and band, and updates every few seconds while you walk.

Your router’s app. Mesh apps list every connected device with its signal as the router sees it, the quickest way to spot a camera or smart plug hanging on by a thread.

How to test WiFi signal strength room by room: the five-minute walk test

A single reading tells you little. The walk test gives you a map, and the map is also where a WiFi installation Singapore survey starts, so it is worth doing properly.

  1. Baseline. Stand a metre from the router or main node and record the reading. It should be -50 dBm or better; if not, the router, its position or its antennas are the first problem.
  2. Walk to where you actually use the WiFi. The bed, the desk, the sofa, the service yard where the washing machine’s smart plug sits. Wait ten seconds at each spot for the reading to settle.
  3. Close the doors. A bedroom reading can differ by 5 to 10 dB with the door open or closed. Test the way you live.
  4. Repeat once in the evening. Signal does not change at night, but noise does. A room that read -62 in the afternoon and feels unusable at 9 pm has an interference problem, not a coverage problem.
  5. Mark it on a floor plan. Green above -60, amber to -70, red below. Two or more red spots in rooms you use is the point where moving the router stops being the answer.

A typical result for a 4-room HDB flat with the router left by the front door: living room -48, master bedroom -63, second bedroom -70, kitchen and service yard -74, the corner behind the household shelter -79. The pattern is so common that an installer can predict it from the floor plan, which is why the fix is rarely a stronger router and almost always a second radio in the right place.

Strong signal but still slow? Signal strength is not speed

A -50 dBm reading promises nothing about speed. It means the radio link is healthy; the data still has to cross a congested channel, a mesh node’s wireless backhaul and the fibre line. If every room reads green and the WiFi still crawls, the cause is upstream of the signal. Our guide on why your WiFi is so slow walks through the two tests that separate a slow line from slow WiFi. Use this article for coverage and that one for speed.

How to fix weak WiFi signal: first, the Singapore causes

Most weak-signal guides are written for timber-framed houses. Singapore homes fail differently.

  • Reinforced concrete walls and floors. HDB flats and most condos are reinforced concrete, and the steel inside reflects radio as much as the concrete absorbs it. As a rule of thumb one RC wall costs a 5 GHz signal 10 to 20 dB, enough to turn a good reading into a weak one in one step.
  • The household shelter. Its walls are far thicker than a partition. The room on the far side of it from the router is the dead zone in most flats, and no setting changes that.
  • The router in the DB cupboard. Fibre terminates near the front door, so the ONT and router are often left inside the DB cabinet or the shoe cabinet beside it, behind a metal door.
  • 5 GHz range. The faster band travels less far and loses more through walls. A phone reading -60 on 2.4 GHz in a bedroom can read -72 on 5 GHz at the same spot.
  • Neighbours. In a dense block a phone can hear thirty networks. They raise the noise floor, so a fair reading behaves like a poor one.
  • Distance and floors in landed homes. One router at the front of the ground floor has no chance at the back bedroom upstairs.

How to improve WiFi signal for free: placement, band, channel, firmware

Try these before spending anything, and re-run the walk test after each.

  1. Get the router out of the cupboard, onto a shelf in the open at chest height or above, antennas vertical. This alone commonly improves far-room readings by 5 to 10 dB.
  2. Move it towards the middle of the home if the cable allows. A router by the front door covers the corridor outside as well as the living room.
  3. Put the right devices on the right band. Phones and laptops near the router on 5 GHz; smart plugs, bulbs and far-room devices on 2.4 GHz. If the bands share one name, check which band a struggling device has picked.
  4. Change the 2.4 GHz channel to whichever of 1, 6 or 11 your neighbours use least; a WiFi analyser app shows this. On 5 GHz, leave it automatic unless it has stuck on a crowded channel.
  5. Remove an old extender. A forgotten extender creates a second network name and a half-speed path. If the walk test shows it is not helping, unplug it.

If the far rooms still read below -67 dBm after all six, the problem is physical and the next section is about hardware.

How to extend WiFi coverage at home: extender, mesh or wired access point by home type

Which hardware suits you depends on the shape of the home and whether a cable can reach the weak room.

Home Typical weak-spot reading What fixes it Typical reading after
3-room HDB, router moved to the centre -62 to -68 in one bedroom Usually placement alone; one plug-in extender if a corner stays weak -55 to -62
4-room or 5-room HDB, router by the door -70 to -80 in the far bedrooms and service yard A 2-node mesh with the second node halfway, or one wired access point in the far half if a LAN point exists -50 to -60
Executive maisonette or 2-storey home -75 and worse on the other floor One node or access point per floor, wired together where possible -50 to -60 on both floors
Long condo unit, 1,200 to 2,000 sq ft -70 to -78 at the far end 2 to 3 mesh nodes using the unit’s existing LAN points for wired backhaul -50 to -58
Landed, 2 to 3 storeys -80 and worse at the back of each upper floor Cabled access points on each floor from a PoE switch; mesh only where no cable route exists -45 to -58 throughout

The readings are typical outcomes, not promises for a specific home; a survey replaces them with measured numbers. An extender rebroadcasts a signal that is already weak, so it fixes one room. A mesh system puts a full radio in the weak half of the home and is the standard answer for most flats. A wired access point does the same with a cable behind it and never loses speed to a wireless hop, which is why it wins in landed homes and any flat with LAN points. Our comparison of access points vs mesh covers the decision, and if the cable does not exist yet, structured cabling for the home is how it gets there.

Do WiFi boosters work? Booster, repeater and extender are the same box

“WiFi booster”, “WiFi signal booster”, “repeater” and “range extender” are marketing names for one device: a unit that receives your router’s WiFi and rebroadcasts it. Nothing is boosted. It must sit roughly halfway to the weak room where the signal is still good; placed in the dead zone it rebroadcasts a dead signal. One radio listening and talking at once typically halves throughput, and most create a second network name. For one stubborn corner in a compact flat it works and costs little. For a flat with two or three weak rooms, it is the fix people buy twice before calling someone. Our guide to mesh WiFi vs an extender has the full comparison.

What signal strength you need for streaming, gaming, video calls and smart home devices

  • Video calls and 4K streaming: -60 dBm or better at the sofa and the desk, with -67 as the floor below which calls freeze.
  • Smart plugs, bulbs and switches: almost all are 2.4 GHz only and cope with about -72, but they are the first to drop when evening noise rises. If a plug keeps showing offline, read the signal at the plug, not at your phone.
  • Cameras: -65 or better at the mounting point, often a corridor ceiling or a gate post, exactly where nobody tested. A camera that streams constantly is the strongest case for a cable.
  • Hubs: a Zigbee or Matter hub needs WiFi only for itself; see Zigbee vs WiFi vs Matter for why a crowded 2.4 GHz band hurts both.

Weak WiFi after a renovation or a new router: what changed

A signal that was fine last month and is weak now has a cause you can usually name. A renovation adds a false ceiling with metal framing or a mirrored wardrobe between the router and a room. A contractor tidies the router into the DB cabinet. The ISP swaps the router for one in a different spot. A new WiFi 7 router adds the 6 GHz band, fast but with the shortest range of all, so a phone that joins it in the living room reads worse in the bedroom. A neighbour installs a mesh on your channel. Run the walk test again; the room that changed points at the cause.

What a professional WiFi survey measures that a phone cannot

Your phone reads one radio at one moment. A survey tool samples every spot across both bands and all channels, records signal, noise and interference together, and plots a heat map on your floor plan. It also measures what the phone never sees: how much speed a mesh node loses on wireless backhaul, which channels the block saturates in the evening, whether an existing LAN point passes gigabit, and where a cable can run without hacking. The result is a design, with a before-and-after reading for every room. Roen’s home network work starts with that survey, moves to mesh or wired access points and the cabling behind them, and ends with a signal and speed test in each room at handover.

Frequently asked questions

How do I test my WiFi signal strength?

On a Mac, hold Option and click the WiFi icon to see RSSI in dBm. On Windows, run netsh wlan show interfaces for a percentage. On Android, open the network’s details in Settings. On iPhone, use Apple’s AirPort Utility with Wi-Fi Scanner switched on. Then walk the home and record a reading at each spot you use.

What’s a good WiFi signal strength?

-50 to -60 dBm is good and is the target for rooms where you work, watch or take calls. -67 dBm is the usual floor for reliable video calls. Below -70 dBm is weak and below -80 dBm is unusable.

How do I check my WiFi signal strength in dBm?

Mac shows dBm in the Option-click WiFi panel. iPhone shows it as RSSI in AirPort Utility’s scanner. Many Android phones show dBm in the network details, and any WiFi analyser app will. Windows shows a percentage; halve it and subtract 100 for an approximate dBm figure.

Why is my WiFi signal weak all of a sudden?

Something moved or changed: the router was tidied into a cupboard, a renovation added metal or a mirror between rooms, the ISP swapped the router, a new router is using 6 GHz with shorter range, or a neighbour’s new network raised the noise on your channel. Repeat the walk test and compare room by room.

Can I boost my WiFi signal strength?

You can improve it for free by moving the router into the open and towards the centre of the home, choosing a quieter channel and putting far devices on 2.4 GHz. You cannot amplify a signal through a concrete wall; past that point the fix is a second radio, a mesh node or a wired access point, placed in the weak half of the home.

Do any WiFi boosters actually work?

Yes, for one weak room, if the booster sits halfway between the router and that room where the signal is still good. They do not work for a whole flat with several weak rooms, because they halve throughput and rebroadcast whatever weak signal they receive. For that, use mesh or wired access points.

WiFi that reaches the last bedroom

Roen surveys the home with proper tools, designs the mesh or wired access point layout around your floor plan, installs the cabling behind it and hands over with a signal and speed reading in every room.

Planning a smart home install?

Tell us what you have in mind and the Roen team will come back to you.

WhatsApp 8986 1961 Contact us