Ceiling fan installation cost in Singapore runs from about S$60 for a straight swap at an existing point on a concrete ceiling to a few hundred dollars once a new wiring point, a false ceiling or a high ceiling is involved, going by the price tables Singapore installers had published on 22 September 2026. The fan is extra. What moves the number is not the brand but four things about your ceiling and wiring: the fan’s weight and control, what the hook goes into, whether a live point already exists, and what sits on the wall. This guide takes the four drivers in turn, quotes the published market ranges with sources, and explains which steps Singapore law reserves for a licensed electrical worker.
What decides ceiling fan installation cost in Singapore
Every quote comes down to four questions, in this order:
- The fan: its weight, AC or DC motor, and whether it carries a light kit.
- The ceiling and the hook: bare concrete slab, plasterboard false ceiling, or a ceiling above 3 m.
- The wiring point: an existing fan or light point you can reuse, or a new point run from the nearest circuit.
- The control: a wall regulator, a remote receiver, a smart wall switch or a Wi-Fi module.
The first two set the mounting labour. The third is where ceiling fan installation cost can double, because new wiring is regulated work. The fourth is small money but decides whether the fan ends up in your smart home app. If any part of the job touches the wiring, the person doing it should be an electrician Singapore regulators recognise: an EMA-licensed electrical worker, not a handyman with a drill.
Driver 1: the fan itself, its weight and its motor
Swapping a light fitting for a fan of similar weight is the cheapest job on any price list. A heavy AC-motor fan with a light kit needs a hook rated for the load; a DC-motor fan needs its receiver wired into the canopy and paired, which is why FixMove lists “DC fan with remote/app” separately from S$100.
Weight matters for a second reason in HDB flats. HDB’s electrical works guidelines list ceiling fan installation as permit-free subject to conditions: the fan should not exceed 6 kg, the clear height from floor to blades must be at least 2.4 m, and the expanding bolt must not exceed 8 mm in diameter or 40 mm plug depth. Home Genie puts typical fan weights at 5 to 15 kg, so check the spec sheet.
Driver 2: the ceiling and the hook
Concrete slab
Most older HDB flats have a bare reinforced-concrete slab: a new hook is a drill, an anchor bolt and a bracket, which FixMove prices at typically S$100 to S$140. Home Genie’s and KDK’s S$60 basic installations both assume concrete with an existing point under 3 m.
Ceiling fan false ceiling installation
Plasterboard cannot carry a spinning fan. The installer opens the board, fixes timber or steel backing to the slab, drops the mount through and patches, which is why every table has a false-ceiling line: FixMove S$180 to S$280, Home Genie S$80 to S$150 on top of basic, Get Handyman from S$180, KDK S$265 per fan. If you are still in renovation, have the backing put in before the board goes up.
High ceilings and downrods
Above about 3 m the installer needs a platform and the fan a longer downrod. Home Genie adds S$50 to S$100 above 3 m; KDK lists S$180 to S$250 extra for 3.6 m to 4 m.
Driver 3: existing point or new wiring
If a ceiling rose with live, neutral and earth is where you want the fan, the electrical part is a termination. If not, a cable is run from the nearest lighting circuit, a switch position added and the run tested. In an HDB flat that cable is surface-run in trunking or conduit, because HDB does not allow wiring to be embedded in the RC slab, beams, columns or walls; at renovation it can be concealed above a false ceiling.
Ceiling fan new wiring cost
This is the widest range of the four because cable length varies. FixMove typically S$150 to S$250 for “new point + wiring” including a switch (its body text says S$100 to S$180 per point); Home Genie S$80 to S$150; KDK prices by distance at S$100 per metre surface, including trunking and patching, and S$170 per metre concealed.
Two Singapore-specific steps come with new wiring. It must be carried out or supervised by an EMA Licensed Electrical Worker, because EMA lists “addition, extension or replacement of electrical power points, such as socket-outlets, switches or lighting points” as LEW work. And for additional fan or lighting points in an HDB flat, HDB requires SPSL Form CS/5H to be submitted through your LEW for testing. A price that leaves both out is not the same job; our guide to what an electrician costs in Singapore covers the per-point conventions behind these numbers.
Driver 4: regulator, remote or smart control
An AC fan runs off a wall regulator; a DC fan runs off a receiver in the canopy and needs only an on/off switch. Swapping one for the other is a small line: KDK charges S$25 to supply an on/off switch, S$25 to bypass a regulator or dimmer, and S$22 for Wi-Fi pairing on its Airy series. The model changes when you want the fan in the same app as the aircon and lights. Three routes: a built-in Wi-Fi module, an RF-remote fan paired to an IR/RF bridge, or a smart wall switch. Think twice about the wall switch, because cutting power to a DC fan defeats its speed control. The options are on our smart ceiling fan integration page; budget the controller plus a short pairing visit, not a rewire.
Ceiling fan installation cost Singapore: the published market ranges
The ceiling fan installation cost Singapore installers and retailers had published, read on 22 September 2026, in Singapore dollars, excluding the fan. They are market ranges for comparison, not Roen’s prices; Roen quotes each job after a site check.
| Cost driver | Published market range | Source |
|---|---|---|
| Swap at existing point, concrete ceiling | S$60 to S$120 | Home Genie S$60; KDK S$60; FixMove S$80 to S$120; Get Handyman from S$80; SparkFlow S$90 to S$120 |
| New hook into concrete | S$100 to S$140 | FixMove |
| False ceiling reinforcement | +S$80 to S$150, or S$180 to S$280 all-in | Home Genie; FixMove; Get Handyman from S$180; KDK S$265 |
| High ceiling (above 3 m) | +S$50 to S$250 | Home Genie +S$50 to S$100; KDK +S$180 to S$250 (3.6 m to 4 m) |
| New wiring point | S$80 to S$250 per point, or by the metre | Home Genie S$80 to S$150; FixMove S$150 to S$250; KDK S$100/m surface, S$170/m concealed |
| DC receiver, remote or app pairing | S$22 to S$150 | KDK S$22; FixMove from S$100; SparkFlow S$150 guide |
| Switch, regulator bypass, disposal | S$25 each | KDK |
Read across a row and the spread is scope, not one company being expensive: S$60 assumes an existing point on concrete under 3 m, S$250 includes a new cable run and a switch. Check whether GST is included.
Who may legally do each step
Two of the pages that rank for this term say “BCA-licensed electrician”. Electricians in Singapore are licensed by the Energy Market Authority, not BCA. EMA states that electrical work “should be carried out or supervised by a Licensed Electrical Worker”, including modification of wiring, addition or replacement of switches or lighting points, and work on consumer units or circuit breakers. For a home the class is a Licensed Electrician (up to 45 kVA); every LEW carries a licence card, searchable on EMA’s ELISE portal.
| Step | Regulated? | Who does it |
|---|---|---|
| Hook into concrete or backing above a false ceiling | Building work, not electrical | Installer; HDB fan conditions (6 kg, 2.4 m, 8 mm bolt) still apply |
| Like-for-like swap at an existing point | Grey area; safest read is LEW-supervised | Retailer installers, DB off and tested dead |
| New fan point, extended wiring, new switch position | Yes, EMA lists it as LEW work | Licensed Electrical Worker, with SPSL Form CS/5H in an HDB flat |
| Any work at the DB board or a new circuit | Yes | Licensed Electrical Worker |
| Pairing a Wi-Fi module, remote or bridge | No, once the fan is wired | Installer or smart home integrator |
Our post on when a licensed electrician (LEW) is required draws the line between what a homeowner may touch and what the law reserves.
Ceiling fan installation HDB: permit, conditions and working hours
HDB does not require a permit for a ceiling fan or for new fan and lighting points, but it attaches conditions, and unauthorised work has to be made good at your cost:
- Fan not exceeding 6 kg; at least 2.4 m clear height to the blades; expanding bolt not exceeding 8 mm diameter and 40 mm plug depth.
- No embedding of wiring in the RC slab, beam, column, wall or plaster; new wiring in metal or high-impact PVC conduit or PVC trunking.
- SPSL Form CS/5H submitted for testing of new wiring through your LEW; installation by an EMA-licensed contractor.
- No work before 8 am or after 6 pm; noisy work only on weekdays between 9 am and 5 pm.
One adjacent job does need a permit: flats without higher electrical loading need HDB approval for new 15 A aircon points; if you are adding aircon at the same time, read our guide to upgrading HDB electrical loading first. On the buying side, HDB households have received Climate Vouchers since 15 April 2024 that can be spent on direct current fans among twelve product types; they can be claimed until 31 December 2027 and cover the purchase, not the installation.
Condo and landed homes: what changes
In a condo the ceiling is more often plasterboard, which puts the job in the false-ceiling band, and the MCST usually wants a renovation application, a deposit and a working-hours window. Landed homes add downrods over stairwells and longer cable runs. Neither changes who may do the wiring: the LEW rule is EMA’s and applies to every home in Singapore.
To get a ceiling fan installation cost Singapore installers can quote like for like, send a photo of the ceiling where the fan goes, a photo of the nearest light point and switch, the ceiling height, the fan model or weight and motor type, and how you want to control it, and ask each quote to name its assumptions in the four-driver order above.
Frequently asked questions
How much does it cost to install a ceiling fan in Singapore?
The ceiling fan installation cost Singapore providers publish starts at about S$60 to S$120 in labour for a swap at an existing point on concrete, per Home Genie, KDK, FixMove and Get Handyman (22 Sep 2026). A false ceiling adds S$80 to S$150 or takes the job to S$180 to S$280; a new wiring point adds S$80 to S$250. Market ranges, not Roen’s prices.
Do you need to run new electrical wires for a ceiling fan?
Only if there is no fan or light point where you want the fan. If a rose is there, the fan is wired to it; if not, a Licensed Electrical Worker runs a new point in surface conduit (HDB) or above a false ceiling at renovation, and files SPSL Form CS/5H for testing.
Can I install a ceiling fan myself in an HDB flat?
You can hang a fan on an existing hook, but new wiring, a new point or a switch change is work EMA reserves for a Licensed Electrical Worker, and HDB expects an EMA-licensed contractor working to its conditions (6 kg fan, 2.4 m clearance, 8 mm bolt).
How long does ceiling fan installation take?
Under an hour for a swap on concrete, per FixMove (45 to 60 minutes) and Home Genie (30 minutes to 1 hour); 1.5 to 3 hours for a new point or a false-ceiling reinforcement.
Are there HDB rules for a new fan installation?
Yes. No permit, but HDB sets a 6 kg fan limit, 2.4 m clear height, an 8 mm maximum bolt, no embedded wiring, SPSL testing of any new point through your LEW, and working hours of 8 am to 6 pm with noisy work on weekdays 9 am to 5 pm only.
Fan point, hook and smart control, wired by a licensed team
Roen works with EMA-licensed electrical workers to fit new fan points, reinforce false ceilings and set up remote, wall-switch or app control, so the fan you buy is mounted to the slab, wired to code and in the same app as your aircon and lights.